Product ID:SATINHIDE LATEX ENAMEL-ARABIAN BEIGE, 88-33
MSDS Date:12/22/1992
FSC:8010
NIIN:00N042561
MSDS Number: BSXVJ

PPG INDUSTRIES INC

4325 ROSANNA DR
ALLISON PARK, PA 15101
US

Emergency Phone: 412-492-5555;304-843-1300

Info Phone: 216-572-6111;800-441-9695

Cage: 47695

PPG INDUSTRIES INC

PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

LONG-TERM STUDY DEVELOPED LUNG TUMORS. STUDIES

RTECS: 9999999ZZ

RISK OF CANCER FROM EXPOS. POTNTL FOR INHAL OF

RTECS: 9999999ZZ

OVEREXP ARE NOT EXPECTED, THERE IS NOT SIGNIFICANT

RTECS: 9999999ZZ

ETHER (DEGBE).DEGBE CONSUMED IN DRINKING WATER AT LOW

RTECS: 9999999ZZ

KIDNEY, SPLEEN, OR TESTES.

RTECS: 9999999ZZ

TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 20-25%

OSHA PEL 10 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST

PEL/TLV 2 MG/M3

CAS: 1332-58-7

RTECS: GF1670500

Fraction By Weight: 2-5%

OSHA PEL 10 MG/M3TDUST,5RDUST

ACGIH TLV: 10 MG/M3 TDUST

ETHANOL, 2-(2-BUTOXYETHOXY)-; (DIETHYLENE GLYCOL MONOBUTYL

CAS: 112-34-5

RTECS: KJ9100000

Fraction By Weight: 1-20%

WATER; (TAP WATER)

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 20-25%

WATER; (DEIONIZED WATER)

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 30-35%

FILM FORMERS, RESINS, AND ADDITIVES

Fraction By Weight: 20-25%

LD50 LC50 Mixture:NONE LISTED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INGEST: HARMFUL/FATAL IF
SWALLOWED. EYE: CAUSES IRRIT. SKIN: MAY CAUSE SLIGHT IRRIT. MAY BE
ABSORB THRU SKIN. INHAL: VAP & SPRAY MIST MAY BE HARMFUL IF
INHALED. VAP GEN AT ELEV TEMPS IRRIT EYES , NOSE & THROAT. CHRONIC:
AVOID LONG TERM & RPTD CONT. PROD CONTAINS TITANIUM DIOXIDE.
ANIMALS INHALING MASS (SUPDAT)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:REDNESS, ITCHING, BURNING SENSATION AND VISUAL
DISTURBANCES MAY INDICATE EXCESSIVE EYE CONTACT. DRYNESS, ITCHING,
CRACKING, BURNING, REDNESS, AND SWELLING ARE CONDITIONS ASSOCIATED
WITH EXCESSIVE SKIN CONTACT.
Medical Cond Aggravated by Exposure:NOT APPLICABLE.

First Aid:INGEST: DO NOT INDUCE VOMIT. EYE: FLUSH IMMED W/PLENTY OF
WATER FOR AT LST 15 MINS. SKIN: FLUSH IMMED W/PLENTY OF WATER
FOLLOWED BY WASHING W/SOAP & WATER. INHAL: REMOVE TO FRESH AIR.
APPLY ARTF RESP & OTHER SUPPORTIVE MEASURES AS REQD. OTHER: IF
INGEST, ANY TYPE OF OVEREXP OR SYMPS OF OVEREXP OCCUR DURING OR
FOLLOWING USE OF PROD,CONT POIS CNTRL CNTR,EMER ROOM/PHYS IMMED;
HAVE MSDS INFO AVAIL.

Flash Point Method:PMCC
Flash Point:0F,-18C
Extinguishing Media:USE NFPA CLASS B EXTINGS (CARBON DIOXIDE, DRY CHEM
OR UNIVERSAL AQUEOUS FILM FORMING FOAM) DESIGNED TO EXTING (SUPDAT)
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT
EQUIP.WATER SPRAY MAY BE INEFT. WATER SPRAY MAY BE USED TO COOL
CLSD CNTNRS TO PVNT PRESS BUILD-UP & POSS (SUPDAT)
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE OR BURST
(DUE TO BUILD-UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

Spill Release Procedures:PROVIDE MAXIMUM VENT. ONLY PERS EQUIPPED WITH
PROPER RESPIRATORY AND SKIN AND EYE PROTECTION SHOULD BE PERMITTED
IN AREA. REMOVE ALL SOURCES OF IGNITION. TAKE UP SPILLED MATL
W/SAWDUST, VERMICULITE, O R OTHER ABSORB MATL & PLACE INTO
CNTNRSFOR DISP.
Neutralizing Agent:NONE LISTED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LRG
QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED FOR STORAGE OF NFPA
CLASS IIIB COMBUSTIBLE LIQS. PROT FROM FREEZING.
Other Precautions:IF MATERIAL IS PART OF A MULTIPLE COMPONENT SYSTEM,
READ MATERIAL SAFETY DATA SHEET(S) FOR OTHER COMPONENT OR
COMPONENTS BEFORE BLENDING AS RESULTING MIXTURE MAY HAVE HAZARDS OF
ALL OF ITS PARTS.

Respiratory Protection:WHERE VENTILATION IS INADEQUATE, USE SUITABLE
RESPIRATOR. WEAR NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR
EXPOSURE OF CONCERN .
Ventilation:PROVIDE GEN DILUTION/LOC EXHST VENT IN VOL & PATTERN TO
KEEP CONC OF INGS BELOW LOWEST SUGGESTED EXPOS LIMITS, (SUPDAT)
Protective Gloves:NITRILE, NEOPRENE, OR LATEX GLOVES.
Eye Protection:ANSI APPRV CHEM WORK GOGGLES
Other Protective Equipment:WEAR PROTECTIVE CLOTHING, INCLUDING
IMPERMEABLE APRON CONSTRUCTED OF NITRILE, NEOPRENE, OR LATEX.
Work Hygienic Practices:CLEAN OR DISCARD CONTAMINATED CLOTHING AND
SHOES.
Supplemental Safety and Health
EXTING MEDIA: NFPA CLASS IIIB COMBUST LIQ FIRES. FIRE FIGHT PROC:
AUTOIGNIT OR EXPLO WHEN EXPOS TO EXTREME HEAT. IF WATER USED, FOG
NOZZ ARE PREF. VENT: LEL IN FIRE & EXPLO HAZ DATA BELOW STATED
LIMIT , & TO REMOVE DECOMP PRODS DURING WELDING/FLAME CUTTING. EFTS
OF OVEREXP: QTYS OF TITANIUM DIOXIDE DUST IN (ING 7)

HCC:N1
Boiling Pt:B.P. Text:>212F,>100C
Vapor Pres:17.3
Vapor Density:HVR/AIR
Spec Gravity:1.24
Evaporation Rate & Reference:33 (BUTYL ACETATE=100)
Solubility in Water:64.2%
Appearance and Odor:VISCOUS LIQUID W/AN ODOR CHARACT TO CHEM FAMILY &
ANY SOLVS LISTED IN ING SEC.
Percent Volatiles by Volume:68.90

Stability Indicator/Materials to Avoid:YES
STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NONE LISTED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRODUCE HAZ DECOMP PRODS WHEN
HEATED. WELDING, BRAZING, OR FLAME-CUTTING MAY PRODUCE FUMES INCL:
CARBON MONOXIDE.

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL, AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WA STE MANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.